5 Solutions to the Samsung 990 Pro SSD Health Decline Problem

Are you facing issues with the declining health of your SSD? If you're concerned about the health status of your Samsung 990 Pro SSD, you've come to the right place. In this article, we will delve into the reasons behind the decrease in Samsung 990 Pro SSD health and offer potential solutions:

Overview of Samsung 990 Pro SSD Health Concerns

Samsung SSDs are a renowned hardware manufacturer. However, numerous users have reported that the Samsung 990 Pro SSDs are experiencing rapid degradation. Some drives have exhibited a decline in health by over 10% within just days or weeks. Here's a typical scenario illustrating the Samsung 990 Pro SSD health degradation issue:

The Samsung SSD health sudden decline is a significant concern. This issue was previously observed with the 980 Pro SSD as well. Samsung is said to be releasing a new firmware update for the 990 Pro SSD to address its health status issue. However, Samsung has not offered an official explanation.

To address the issue swiftly, this article compiles common reasons for health deterioration of the Samsung 990 Pro SSD based on feedback from multiple users. It then offers solutions to rectify the problem. Continue reading to discover the most suitable solution for you.

You might also like:

Why Does Samsung 990 Pro SSD Health Decline?

There have been reports of rapid degradation in the health of the Samsung 980 Pro SSD series, and it is possible that the 990 Pro and 980 Pro series might exhibit similar issues. Drawing from past hardware problems, we have examined some potential causes for the swift decline in the health of the Samsung 990 Pro SSD:

1. **Existence of Bad Blocks:** Some 980 Pro users have experienced SSD failures after 6 months to a year of usage due to bad blocks. The 990 Pro might encounter the same issue. 2. **Firmware Problems:** The 980 Pro has addressed SSD issues through a firmware update. The 990 Pro might also require a firmware update to resolve potential problems. 3. **Driver Failure:** Samsung drivers might be outdated. Running a driver update could be beneficial. 4. **Incorrect Slot Installation:** Some users have mistakenly installed the SSD in a gen3 PCIe slot instead of the PCIe 4 slot. Reinstalling it in the correct slot might solve the issue. 5. **Incompatibility with Windows:** Affected SSDs, especially those used for operating systems, might not function well with Microsoft Windows, particularly the Samsung 990 Pro. 6. **SSD Wear:** Frequent read and write operations within a short duration can cause SSD sectors to wear out, leading to a decline in the drive's health. 7. **Manufacturing Defects:** There might be a batch of SSDs with specific issues resulting from manufacturing defects.

We've offered some potential solutions to these issues. Keep reading to address the Samsung 980 Pro SSD health rapidly declining error.

How to Address Samsung 990 Pro SSD Health Decline

If you're noticing a sudden drop in performance with your Samsung 990 Pro SSD, don't worry. Instead, follow these solutions to address the health degradation issue and enhance the SSD's performance.

Solution 1: Check and Repair the File System

If the SSD is experiencing health issues, it could be a corrupted SSD. You can inspect the drive for problems and rectify any bad sectors. The Partition Master Pro tool offers a comprehensive and efficient solution to help enhance the health of your Samsung 990 Pro SSD.

It can scan for bad sectors, repair the file system, reconstruct the MBR (Master Boot Record) on the SSD, and format the SSD in order to address any issues with your SSD. Here are the steps to check and repair the file system of the 990 Pro SSD: 1. **Check Disk for Errors**: - Open "Command Prompt" as an administrator. - Type `chkdsk /f /r C:` (replace 'C:' with the actual drive letter of your 990 Pro SSD) and press Enter. - This command will check for and fix any file system errors. 2. **Repair File System**: - In "Command Prompt," type `fsutil fsinfo repairs C:` (replace 'C:' with the appropriate drive letter) and press Enter. - If the output shows that the file system needs repair, run `chkdsk /f /x /c C:` (replace 'C:' accordingly), then reboot the system. 3. **Rebuild MBR**: - Run Command Prompt as an administrator. - Type `bootrec /fixmbr` and press Enter. - This command will replace the MBR on your SSD with a standard Windows MBR. 4. **Format the SSD**: - Go to "This PC" or "My Computer," right-click on the 990 Pro SSD, and select "Format." - Choose the appropriate file system (e.g., NTFS), allocation unit size, and ensure the "Quick Format" option is checked. - Click "Start" to format the SSD, but be aware that this will erase all data. Remember to backup any important data before performing these operations, as they may result in data loss.

Step 1. Right-click the problematic partition.

Step 2. Choose "Tools" > "Check File System".

Step 3. Confirm whether you want to hide the partition or not.

Step 4. In the Check File System window, select the "尝试修复找到的错误" option.

Step 5. Click "Start" to begin checking for errors on your partition.

Furthermore, if you wish to perform more repairs on your SSD, please click on the following link to access a comprehensive guide:

Solution 2: Update SSD Firmware

If your Samsung 990 Pro SSD is showing high wear and tear, you can resolve this issue with the most recent firmware update. The firmware update addresses the underlying issue and prevents the wear and tear indicators from increasing further by:

Step 1. Press and hold Windows+X, then choose Device Manager from the options.

Step 2. Right-click on the target drive, select Properties, go to the Hardware ID tab, and save the settings.

Step 3. Run the SSD firmware update tool and follow the on-screen instructions to finish the process.

Solution 3: 4K Aligned SSD

4K alignment for SSD is a crucial technique for enhancing SSD performance. With Partition Master software, you can optimize the disk by eliminating system junk and deleting large files. Optimizing Samsung SSDs contributes to boosting the performance of SSDs and maintaining them in optimal condition.

With just a few clicks, even novices can become proficient in enhancing SSD performance.

Step 1. Go to "Toolkit" and select "4K Alignment".

Step 2. Select the disk that you want to align. Click the "Start" button.

Furthermore, if your 990 or 980 Pro SSD's speed decreases, this method can effectively enhance the slow write speed issue on the Samsung 980 Pro.

Solution 4: Update Samsung SSD Drivers

Each component of the computer functions with a specific driver. If the driver is outdated, it might result in the SSD not functioning properly. You can enhance the stability and performance of your Samsung SSD by updating its driver.

If you're familiar with your computer system, you can use Device Manager to update the drivers manually. Alternatively, you can try using Driver Handy for automatic updates. This tool can automatically scan more than 5 million drivers and update the appropriate ones for you.

Just click "Scan," wait a little while, and then click "Update" on the right to update it.

Solution 5: Replace the Drive

If your Samsung SSD is still under warranty, you can reach out to Samsung Customer Support and attempt to get it repaired. Alternatively, you can request a replacement drive from Samsung. The issue with the degradation of the Samsung 990 Pro deserves further investigation by Samsung.

Bonus Tip: How to Check Samsung 990 Pro SSD Health Checking the health of your Samsung 990 Pro SSD is essential to ensure its optimal performance and longevity. Here's a step-by-step guide on how to do it: 1. **Download Samsung Magician Software:** Visit the [Samsung官网](https://www.samsung.com/semiconductor/minisite/ssd/tools/) and download the latest version of Samsung Magician software, which is specifically designed for Samsung SSDs. 2. **Install and Launch the Software:** Install the downloaded software on your computer and launch it. Make sure your Samsung 990 Pro SSD is connected to your system. 3. **Connect the SSD:** If the SSD is in an external enclosure or not directly connected to your motherboard, ensure it's properly connected via USB or SATA interface. 4. **Detect the SSD:** Upon launching Samsung Magician, the software should automatically detect your 990 Pro SSD. If not, click on "Add Drive" and follow the prompts to locate and add the drive. 5. **Check the Status:** In the main interface, you'll see an overview of your SSD's status. Look for the "Health Status" indicator, which will display "Good" if the drive is functioning normally. 6. **View S.M.A.R.T. Data:** S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) provides critical information about the drive's health. Click on "S.M.A.R.T. Status" to view the detailed S.M.A.R.T. attributes. Any failed or failing attributes may indicate potential issues. 7. **Run a Diagnostic Test:** To further assess the drive's health, click on "Performance Benchmark" and then "Advanced Test." Choose the "Drive Self-Test" option to run a thorough diagnostic scan. This may take some time, but it will help identify any underlying problems. 8. **Regular Monitoring:** Periodically check your SSD's health using Samsung Magician to catch any potential issues early on. Keep the software up-to-date to ensure compatibility with the latest firmware updates for your 990 Pro SSD. By following these steps, you can stay informed about your Samsung 990 Pro SSD's health and take necessary precautions to maintain its top-notch performance.

SSD health deterioration can lead to numerous issues, and to prevent these problems, users can monitor the condition of their Samsung SSD using tools like Partition Master or Samsung Magician. Follow the links below to learn about possible drive failures:

How to Check Samsung SSD Health on Windows [100% Working Solutions]

This guide provides an overview of the reasons and tools to check the health of your Samsung SSD on Windows. It will discuss how to monitor the SSD's real-time health status and ensure it is functioning optimally.

Conclusion

This guide examines several factors contributing to the rapid decline in health of the Samsung 990 Pro SSD. Drawing from previous experiences with the 980 Pro models, firmware issues are identified as the most probable cause for this issue. Additionally, the presence of bad sectors or corruption in the file system can also contribute to the deterioration of the drive's health.

For this reason, we provide the Partition Master tool to repair your SSD and enhance its performance. This utility offers several functions, such as SSD partition alignment, file system checking, and more.

Frequently Asked Questions About Samsung 990 Pro SSD Health Decline

This section provides frequently asked questions and swift responses regarding the Samsung 990 Pro SSD health decline issue. Hopefully, it will be informative for you.

1. Why did the SSD's health decrease?

There are numerous reasons behind the degradation of SSD health. Frequent writing operations can lead to wear and tear on SSD sectors, or there might be an incorrect file system present on the SSD. All these factors can contribute to the failure of SSDs.

2. How much health is sufficient for SSD?

Each write operation to the data reduces the lifespan of an SSD. For a brand new SSD, it's typical to have 100% health. After a few years, this might decline to 60%. Once it drops to 30%, it's advisable to start considering a replacement.

3. Is the Samsung 990 Pro SSD fixed?

An issue with the firmware was responsible for the unusual Samsung health problem. Samsung has issued a firmware update to address this concern. If the problem persists, you may attempt additional solutions from this article, such as updating the driver and ensuring 4K alignment for the SSD.